Once you’ve put together the tools needed to repair the screen, it’s time to start repairing your device. Place the laptop in a closed position on the surface you chose while keeping the equipment nearby.
Switch off the power source.
Switch off your laptop and ensure it’s connected to any source of power to avoid the possibility of electroshock. Additionally, it is beneficial to remove the battery to prevent any problems later on.
Once you’ve completed this, you’ll have to locate the stickers covering the screws that sit in the bezel of the laptop screen. You’ll usually find them at the side of the screen, close to where hinges would be in the event that the laptop screen were to be opened.
Be sure to take care to remove all screws and labels
Then, you’ll need to remove the pins to remove the labels on the bezel, to ensure that you don’t harm the bezel. It’s essential to put on labels in the future when your laptop screen is set up correctly , therefore, ensure you don’t lose the labels and keep the stickers on the side that is sticky in order to reuse the labels. Store them in a safe area so that when you have the time to install your new laptop screen, they’re easy to access.
You’ll then need to use a screwdriver in order to remove the screws that are visible. It is possible to encounter issues based on the level to which they were screwed when they were created. In most cases, if your old laptop screen was properly aligned it shouldn’t be a problem to take the screws off. Place them in the dish , and make sure not to damage any.
Remove bezel
It’s time for you to remove the bezel. Be careful when taking off the bezel of your screen as it’ll be needed to replace it when the laptop screen is replaced. By using a putty knife or another flat object that you can take your screen out of your laptop’s case and router hwic-2t.
It might require some effort to take it off completely. Be careful when you detect the noise of plastic snapping. It’s the result of breaking tabs that are made of plastic and connect the screen in place to the case. If you’re experiencing difficulty in taking away the laptop screen the screws that are on the bottom might not be tight enough, and you need to be sure to loosen them up slightly before trying again.
There are other issues that your screen may become caught on the hinges. If you move it gently, you should be able to free its frame.
Detach the LCD
One of the most challenging aspects of replacing the screen on your laptop will be removing the LCD. Be sure that the bezel is removed completely in order to give you complete access to your LCD. It’s attached to your laptop’s aluminium frame. you’ll have to take it off on both ends. And the zebra warranty check is done.
There are two screws which must be removed from top corners before you can move the laptop screen further away from its frame. There could be other screws that hold your LCD’s frame to its sides. They should be removed as well. In some cases, it’s possible for heavy duty tape to be used instead.
Unplug the cables from the connectors.
Once you’ve removed all of the screen’s accessories the screen will be sitting on top of the keyboard. It’s difficult to make sure there’s enough space between the frame and LCD. However, be sure to avoid damaging the video cable that runs through the display’s front display , and then into the frame of the laptop. If the cable has been damaged, it will require professional help in fixing it.
It is the next thing to do, disconnecting the cable for the LCD. The connectors are located on the upper part of the laptop screen, but they can also be located on the lower side that is the bottom. There’s a good chance that glue was used to connect them, and then you’ll have to take one off of the other. It could also be tape that needs to be removed. But, at the end of the day, it’s fairly simple to take your monitor from the video port. It should be placed away from any equipment.
Set up the screen with the latest version.
After you’ve removed the screen, and put it back into its place, you should be able to determine the location where your new screen will go. Set it down within the frame, so it fits perfectly. Once it’s there, attach the video connector to ensure it’s in the exact spot the initial LCD was. Make sure that it’s in the most perfect alignment. Then attach it with tape or adhesive.
Reattach bezel
After finishing, you must make sure the sides are securely secured. Replace the screws onto the edges, and then on top or reconnect any tape that was used to secure everything. Once everything is fitted and secured, you can insert the screen into. The screen should be aligned so that it is securely inserted into the frame of the screen. It should not be difficult to unlatch.
Install the screws back into the bezel after you’ve confirmed that all the screws are securely snapped in the proper location. There shouldn’t be cracks on any edges of the laptop screen. Once the screws have been installed, reattach the screw covers using a needle pin.
Power up
You’ll then be able to reboot your computer. Install the battery and connect your computer to an electrical source prior to switching it on. If you do not see any display, you’ll need to check to make sure that everything is in place.
Have fun with a fantastic DIY repair for your computer screen
The repair of the screen on your laptop doesn’t have to be done by a professional. If you have the time and energy, you may be able to save yourself some money by completing the repair yourself. You can do this by understanding the display costs for laptops. In the event you take these guidelines and follow the instructions, you’ll be able to make your laptop’s display operational in just a couple of hours.